✦ Guides

How to Print a 4-Cut Photo Strip at Home

You do not need a dedicated strip printer to get a clean 4-cut photo strip on paper. Here is how to set up your file, choose your paper, and avoid the two mistakes that make home prints look cheap.

Y2KIBOOTH blog cover

If you want to print 4-cut photo strip images at home, you need much less than a dedicated photo booth printer. Any printer that handles 2 by 6 inch photo paper can do the job, and most modern home printers fit two strips onto a single 4 by 6 sheet. The real work happens before the printer starts, in the shot and the settings you choose.

This guide covers the whole chain, from taking a session to pulling a finished strip out of the tray.

How to print 4-cut photo strip images at home

1. Start with a correctly sized file

A 4-cut strip is one tall vertical image with four frames stacked top to bottom, each holding a single shot from the same session. The booth captures four shots with an automatic 3-2-1 countdown before each one, then saves the result as a single HD PNG at 600 by 1722 pixels.

Those dimensions match the real thing. Classic photo booth strips were narrow, roughly two inches wide and six inches tall, so your file already fits the paper you are about to feed it into. Do not crop the white space around it and do not stretch it. Open it once and look before you print. Our guide to 4-cut versus 6-cut photo strips compares the formats.

2. Set the paper size and turn scaling off

This is the single biggest reason home photo strips look wrong. If your print dialog says fit to page or scale to fit, the strip gets resized to the paper and the frames end up at inconsistent sizes with awkward margins.

  • Turn scaling to 100 percent, or choose print at actual size.
  • Set the paper size to 2 by 6 inches for a single strip.
  • Choose a 4 by 6 inch sheet when you want two strips side by side.
  • Enable borderless printing so the artwork runs to the edge.

3. Choose the paper and color settings

Glossy photo paper reads closest to a mall photo booth print, while matte stock is easier to write on. Either works, and the difference matters much less than using photo paper rather than plain office paper.

Print in color unless you want a deliberate black and white look. Keep quality settings on high so fine frame borders do not blur. If a print comes out pale, check borderless and quality before you swap paper.

4. Print one test strip first

Run a single test before a batch. Check the top frame for cropping, the bottom frame for cutoff, and the overall brightness. A test costs one sheet and saves a stack.

Then choose your layout:

  • One strip per 2 by 6 inch sheet for a classic single-strip print.
  • Two strips on one 4 by 6 inch sheet, which is the same space and twice the keepsakes.
  • Six strips together in a 4 by 6 grid for scrapbook pages and gift tags.

5. Let the frame carry the design

Home prints do not have a physical backdrop, so the digital frame has to do that job. There are six looks in the booth: Chrome, Bubble, Lilac, Lime, Midnight, and Glitch. Each one adds its own background, border, and color treatment.

Use the same frame for all four shots in a session. If you switch frames between shots, the strip looks stitched together. The four filters, OG, Chrome, Sunset, and Noir, adjust color and grain rather than adding stickers, which keeps a printed strip from looking busy.

For paper, Chrome and Sunset tend to reproduce cleanly on glossy stock. Glitch and Midnight have deeper shadows, so preview them before running a full page.

Small fixes for common print problems

  • Cropped images: scaling is still on, or borderless is off and the printer is clipping the edge.
  • Faded or gray prints: ink level, grayscale mode, or printing on the wrong side of the sheet.
  • Blurry frames: you downloaded a small preview instead of the HD PNG.

Take one session, print a test strip, then work out your layout. When you are ready, open the booth and take your first four shot set.

KEEP READING